RT-4481-5

RT-4481-5 is a decorative PVC rafter tail with a stepped underside and a concave cove that curves up to a squared tip, giving exposed eaves a more detailed, layered outline. It comes in nine sizes and can be used within the HB PVC Soffit System or on its own.

SKU: RT-4481-5 Category: Tag:
Description

RT-4481-5 PVC Rafter Tail 

Where a roof’s rafters run past the exterior wall, their ends, the rafter tails, carry the soffit overhang. On homes with exposed timber framing, the way those ends are cut becomes one of the defining details of the eaves. RT-4481-5 recreates a shaped rafter end in PVC as a decorative feature: it gives the look of exposed rafter tails but is not part of the roof structure.  

Design and where to use it 

The top edge of RT-4481-5 runs straight from the wall to the tip, while the underside is shaped in stages. A small square step first reduces the depth of the tail and is followed by a flat section; a concave cove then curves upward, and a second small step leaves a squared-off tip. Together, these cuts create more shadow lines than a single curve and give each tail a layered, carved appearance. 

This more detailed profile works well where the eaves are a focal point of the elevation, for example on Charleston, Spanish Mediterranean or West Indies-style homes, all styles HB Elements specializes in. It can also be placed as a lookout at a gable end or under a cantilevered deck. For a simpler outline, see the rounded-end RT-4204-1 or the long, shallow curve of RT-4202-3.  

Construction and fitting 

RT-4481-5 is made from cellular PVC with a hollow core, fabricated using HB Elements’ patented system. It is intended as a decorative element only and must not be used to carry structural loads. 

Installation uses the cleat and adhesive supplied with the tail, and a tail can be trimmed on site if a shorter length is needed. RT-4481-5 can be installed over stucco, wood or cement fiber, and most often over cellular PVC soffits. It needs minimal preparation before painting, so it can be finished in the same color as the fascia and trim.  

How RT-4481-5 fits the HB PVC Soffit System 

The HB PVC Soffit System is typically made up of fascia, soffit panel, frieze board and rafter tails. Fascia closes off the roof edge, soffit panels line the underside of the overhang, the frieze board finishes the line where the soffit meets the wall, and rafter tails such as RT-4481-5 punctuate the eave at regular intervals. Used with HB V-groove or nickel-joint soffit panels, which reproduce the look of 1×6 tongue-and-groove boards, the tails help create a traditional timber-framed roof with tongue-and-groove decking. All four components are also available for use individually.  

Ordering and sizing help 

To get the size right first time, email a PDF set of your plans to info@hbelementsinc.com, then call (954) 784-8216 to review them with an HB representative. You can also download the Rafter Tails Spec Sheet, see the full range of HB rafter tail profiles or watch installation videos in the HB Elements video library.

Additional information
soffit-systems-variations3 1/2″ x 5 1/2″ x 24″, 3 1/2″ x 5 1/2″ x 30″, 3 1/2″ x 5 1/2″ x 36″, 4 1/2″ x 9 1/2″ x 24″, 4 1/2″ x 9 1/2″ x 30″, 4 1/2″ x 9 1/2″ x 36″, 4″ x 7 1/2″ x 24″, 4″ x 7 1/2″ x 30″, 4″ x 7 1/2″ x 36″